Crown XTi1002 Power Amplifier Refurbished

Crown XTi1002 Power Amplifier Refurbished

$409.97
Out of stock
Qty:
SKU: CROXTI1002BU Category:

It looks new. Only been used less than a few hours. Sometimes it only has been opened and tested.

Crown XTi1002 Power Amplifier offers unprecedented value and innovation in a lightweight, professional power amplifier. It’s the smallest and most affordable amplifier in the XTi 2 series — an great solution for driving a smaller venue PA system. It also serves as a fantastic power conditioner, assuring that your system will get clean AC even if you’re working with less-than-optimal power sources.

A number of unique features on the Crown XTi1002 Power Amplifier allow you to control the subtlest details of your sonic output:

Multiband Parametric EQ on Inputs and Outputs
The system software includes a HiQnet Band Manager and System Architect. These allow you to control separate multiband parametric EQs both on the Input and the Outputs! Either EQ can be bypassed when you so desire. The Input EQ also includes High and Low Pass Shelving filters, with Bandpass Gain and Polarity control.

Up to 50 Milliseconds of Delay
The XTi1002’s incredibly handy adjustable Delay control gives you 50 mS of delay, so that you can get your speaker output perfectly aligned and eliminate any trace of phase discrepancy.

Peakx Plus Limiters
The XTi1002 excels even further with its sweet Crown Peakx Plus Limiters. These give you full control over Threshold, Attack, and Release on the peak limiters, to make sure that your dynamic extremes are smoothed out in a way that is sonically and musically agreeable.

Subharmonic Synth
There is also a Subharmonic Synth integrated into the XTi1002’s design, so that you can fine tune Frequency, Gain and Filter Type, allowing for application-specific tuning.

Thoughtful I/O Design for Maximum Versatility
Each input has a single balanced XLR per channel. For audio output, the XTi1002 sports 2 x Neutrik Speakon NL4MP jacks. The Channel-1 Speakon is wired with Channel-1 and Channel-2 outputs for use with an optional 4-conductor cable. The unit also has a Loop-Thru signal from the input connector, allowing you to link each channel to another amplifier when necessary.

Efficient Design, Durable Construction
The Crown XTi1002 Power Amplifier is built rock solid with an all-steel chassis that takes up 1RU of space in a standard rack. The front panel is handsome cast-aluminum. The unit includes integrated cast-aluminum rack handles.

Features

Stereo Wattage: 700W @ 2 ohms, 500W @ 4 ohms, 275W @ 8 ohms
Bridged Mono Wattage: 1000W @ 8 ohms, 1400W @ 4 ohms
Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
New system monitoring provides software visibility of AC line voltage and power supply temperature
Integrated cast-aluminum handles for easy handling and enhanced durability
Locking power cord clip provides a secure connection between the amplifier and power cord
Updated HiQnet Band Manager and System Architect control software
Increased number of presets to a total of 30; 29 of which are user definable

Specifications

Output Power:
700W @ 2 Ohms Stereo (per Channel)
500W @ 4 Ohms Stereo (per Channel)
275W @ 8 Ohms Stereo (per Channel)
1400W @ 4 Ohms Bridged-Mono
1000W @ 8 Ohms Bridged-Mono

Damping Factor 20Hz to 1kHz > 500
Input Sensitivity 1.4Vrms
Input Impedance 20k Ohms (Balanced)
10 kOhms (Unbalanced)
Gain 32.9dB @ 1kHz, 8 Ohm Rated Output
Frequency Response (at 1 watt, 20Hz – 20kHz) +0dB, -1dB
Signal-to-Noise Ratio XTi1002/2002/4002: 100dB (A weighted)
XTi6002: 103dB (A weighted)
Total Harmonic Distortion (THD) < 0.5%

Connections:
Input Connectors: XLR, one per channel
Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
HiQnet USB Connector: Type B, connects to HiQnet network.

Controls Front Panel: Level: Two front-panel rotary level controls, one for each channel
Power Switch: On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen: Backlit liquid crystal display that shows preset and processing status

Indicators: Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
-10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power

Cooling Proportional speed fan with front-to-rear airflow.
Power Consumption 6.8A; no more than 38W at idle
Power Requirements 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
Dimensions 19 x 3.5 x 12.25″ (48.26 x 8.89 x 31.11cm)
Weight 18.5 lbs (8.4kg)
Specialties DSP Includes EQ, Crossover Filters, Delay, and Subharmonic Synthesizer
Protection for Short Circuits, Overloads, and Overheating

Related products