Crown XTi2002 Power Amp & 2 Pig Hog 25ft SPKON to 1/4′ Cables Bundle

Crown XTi2002 Power Amp & 2 Pig Hog 25ft SPKON to 1/4′ Cables Bundle

2-channel Power Amplifier, 800W Continuous/ch at 4 ohms, with HiQnet Band Manager, Peak Plus Limiters, System filters tuning
Out of stock

Crown XTi2002 Power Amplifier is a 2000-watt rack mounted power amp that distinguishes itself with a number of extremely useful precision adjustment controls. Crown XTi2002 also serves as a fantastic power conditioner, assuring that your system will get clean AC even if you’re working with less-than-optimal power sources.

Crown XTi2002’s incredibly handy adjustable Delay control, which gives you 50 mS of delay so that you can get your speaker output perfectly aligned and eliminate any trace of phase discrepancy. There is also a Subharmonic Synth integrated into the XTi2002’s design, so that you can fine tune Frequency, Gain and Filter Type, allowing for application-specific tuning.

Crown XTi2002 excels even further with its sweet Crown Peakx Plus Limiters. These give you full control over Threshold, Attack, and Release on the peak limiters, to make sure that your dynamic extremes are smoothed out in a way that is sonically and musically agreeable.

Pig Hog cables are precisely overbuilt to stand up to the most grueling tour conditions imaginable. They feature extra-thick 8mm wire, performance quality connectors, and tension-resistant stress relief.
High performance speaker cable
8mm high quality rubber outer covering
14 gauge wire
Heat shrink protected connectors


Peak x Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release

Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning

3 User-defined fan mode controls – normal, early and full speed – for matching fan performance to a specific application

Input EQ with bypassable 6-band parametric filter

Input EQ with bypassable 8-band parametric filter

Highpass and Lowpass filters on each channel

Subharmonic Synth with Frequency, Gain, and Filter Type settings

Locking power cord clip provides a secure connection between the amplifier and power cord

Updated HiQnet Band Manager and System Architect control software

Increased number of presets to a total of 30; 29 of which are user definable


Minimum Guaranteed Power, (1 kHz Per channel, both channels driven)
Stereo, 2 ohms (per ch.): 1000W
Stereo, 4 ohms (per ch.): 800W
Stereo, 8 ohms (per ch.): 475W
Bridge-Mono, 8 ohms: 1600W
Bridge-Mono, 4 ohms: 2000W
Integrated Processing
Input EQ: 6 parametric filters per channel with adjustable Q, +/-15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Crossover Filters: Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes +/-15 dB bandpass gain and polarity control.
Output EQ: 8 parametric filters per channel with adjustable Q, +/-15 dB boost/cut. This 8-filter EQ section can be bypassed.
Delay: for signal alignment of driver; 50 mS of total delay.
SubHarmonic Synth: takes the low-frequency content of the input signal and “synthesizes” a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
Peak x Plus Limiter: user defeatable limiter that allows users to control Threshold, Attack, and Release times.
Presets: 30 total presets, 29 of which are user-definable.
Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
Frequency Response (at 1 watt, 20 Hz – 20 kHz): +0 dB, – 1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
Total Harmonic Distortion (THD): <0.5%
Damping Factor 20 Hz to 1 kHz: >500
Crosstalk (below rated power): 20 kHz – 1 kHz: > 70 db
Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal: +22 dBu typical
AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per channel): 8.3A; no more than 38W at idle
Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
Level: two front-panel rotary level controls, one for each channel
Power Switch: On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons: three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen: backlit liquid crystal display that shows preset and processing status
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
– 10 Indicator: Green LED flashes when output signal exceeds
– -10 dB below clip.
– 20 Indicator: Green LED flashes when output signal level exceeds – 20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
Input/Output Connectors
Input Connectors: XLR, one per channel
Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
HiQnet USB Connector: Type B, connects to HiQnet network.
Chassis: Steel
Front Panel: Cast-aluminum
Cooling: Proportional speed fan with front-to-rear airflow.
Dimensions: 19″ (W) x 3.5″ (H) x 12.25″ (D)
Net Weight: 18.5 lb. (8.4kg)

Related products